Best 2008 Saturn Outlook Hitch Options- Video

Today our 2008 Saturn Outlook, we're gonna be taking a look at the best hitch options available. The two hitches we'll be taking a look at today are both class 3, with a 2 inch by 2 inch opening. First off, we have our Curt and that's part number 13424, and then we have our Draw-Tite, and that's part number 75528. As you can see, our Curt has a square tube design, whereas our Draw-Tite has a round tube design. It doesn't rightly matter, cause both can be tucked up behind our bumper, underneath the appearance panel. You'll then be able to remove the appearance panel when you'd like to access the hitch. When it comes to weight rating, our Curt is gonna offer us a 5,000 pound, gross trailer weight, and a 500 pound tongue weight. For our Draw-Tite we're gonna get a 5,000 pound max gross trailer weight, and a 750 pound max tongue weight. Both can be used with weight distribution. When using weight distribution it bumps the Curt up to a 6,000 pound max gross trailer weight, and a 600 pound max tongue weight. more

Watch Video

3/3/2017 1:36:02 PM

Best 2010 Saturn Outlook Hitch Options- Video

Today in our 2010 Saturn Outlook, we're going to be taking a look at the best hitch options available. The two hitches we'll be taking a look at today are both Class three with a two inch by two inch opening. First off, we have your Curt and that's part number 13424 and then we have our Draw-Tite and that's part number 75528. As you can see, our Curt has a square tube design whereas our Draw-Tite has a round tube design. It doesn't rightly matter because both can be tucked up behind our bumper underneath the appearance panel. You'll then be able to remove the appearance panel when you'd like to access the hitch. When it comes to weight rating, our Curt is going to offer us a 5000 pound gross trailer weight and a 500 pound tongue weight. more

Watch Video

3/3/2017 1:35:52 PM

Best 2009 Saturn Outlook Hitch Options- Video

Today in our 2009 Saturn Outlook, we're going to be taking a look at the best hitch options available. The two hitches we'll be taking a look at today are both class three, with a two inch by two inch opening. First off, we have our Curt, and that's part number 13424, and then we have our Draw-Tite, and that's part number 75528. As you can see, our Curt has a square tube design, whereas our Draw-Tite has a round tube design. It doesn't rightly matter, because both can be tucked up behind our bumper, underneath the appearance panel. You'll then be able to remove the appearance panel when you'd like to access the hitch. When it comes to weight rating, our Curt is going to offer us a 5,000 pound gross trailer weight, and a 500 pound tongue weight. For our Draw-Tite, we're going to get a 5,000 pound max gross trailer weight, and a 750 pound max tongue weight. more

Watch Video

3/3/2017 1:35:48 PM

Best 2007 Saturn Outlook Hitch Options- Video

Today on our 2007 Saturn Outlook we're going to be taking a look at the best hitch options available. The two hitches we'll be taking a look at the today are both Class 3 with a 2" by 2" opening. First off, we have our CURT. That's part number 13424. Then we have our Draw-Tite. That's part number 75528. As you can see, our CURT has a square tube design, whereas our Draw-Tite has a round tube design. more

Watch Video

3/2/2017 3:47:07 PM

Trailer Hitch Installation - 2008 Saturn Sky- Video

Today, on this 2008 Saturn Sky, we're going to review and install the Curt Class One inch and a quarter receiver hitch, part number C11114. All right, this is what the hitch looks like when it's installed on our Saturn Sky. At first glance, you can see that the body of the hitch does sit below the bumper cover, here, due to the way the vehicle is constructed, so it has to be sitting down a little bit low like this. We'll cover some more details here. We notice we've got a nice reinforcement ring around our inch and a quarter hitch, here. Most others do not have this one, so it's a nice touch. This uses a half inch hitch pin, that does come with the kit. more

Watch Video

12/7/2016 10:09:40 AM

Trailer Hitch Installation - 2002 Saturn S Series - Hidden Hitch- Video

All right, today on this 2002 Saturn S series, we're going to install part number 60839 from Hidden Hitch. This is what the hitch looks like once installed on the car. Next, we'll give you some measurements to help you out in selecting some accessories such as the bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be about 11 inches and from the center of the hitch pin hole to edge of the bumper will be about 8 inches. Now we'll go ahead and show you how the hitch is installed. The first thing we need to do is get our vehicle ready. To do that, we want to go on the inside of the vehicle and remove the carpeting and the spare tire cover from inside the trunk. more

Watch Video

12/31/2014 4:25:05 PM

Trailer Hitch Installation - 2002 Saturn S Series - Draw-Tite- Video

Today on this 2002 Saturn S Series we're going to install Part Number 24620 from Draw Tite. This is what the hitch looks like once installed on the car. Next we'll give you some measurements to help you out in selecting some accessories, such as a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be about 11 inches. From the center of the hitch pin hole to the edge of the bumper will be about 8 inches. Now we'll go ahead and show you how the hitch is installed. more

Watch Video

12/31/2014 4:20:34 PM

Trailer Hitch Installation - 2007 Saturn Aura - Hidden Hitch- Video

Today on our 2007 Saturn Aura we'll be installing the Hidden Hitch Trailer Hitch Receiver with Drawbar. It's a Class II hitch with a 1-1/4" receiver, part number 90194. This is what the hitch looks like installed on our Saturn. The top of the receiver to the ground is about 9" and 6-1/2" from the center of the hitch pin hole to the rear bumper. Now we'll go show you how the hitch is installed. The first thing I'm going to do here is show you the mounting points for the hitch and out behind the bumper. Now that we've identified the mounting points we'll take our bolt guide and run it through the bumper structure. First we'll take our block with the square hole, insert it over the bolt guild, and then we'll thread our carriage bolt into the bolt guide. more

Watch Video

12/15/2014 2:33:54 PM

Trailer Hitch Installation - 2007 Saturn Aura - Draw-Tite- Video

Today on our 2007 Saturn Aura we'll be installing the Draw-Tite Trailer Hitch with the 1-1/4" receiver, part number 36479. This is what the hitch looks like installed on our Saturn. The top of the receiver to the ground is about 9" and 6-1/2" from the center of the hitch pin hole to the rear bumper. Now we'll go show you how the hitch is installed. The first thing I'm going to do here is show you the mounting points for the hitch and out behind the bumper. Now that we've identified the mounting points we'll take our bolt guide and run it through the bumper structure. First we'll take our block with the square hole, insert it over the bolt guide and then we'll thread our carriage bolt into the bolt guide. more

Watch Video

12/15/2014 2:32:49 PM

Trailer Hitch Installation - 2006 Saturn Vue - Hidden Hitch- Video

Today on our 2006 Saturn Vue we'll be installing the Hidden Hitch, part number 90145. Now here's what our hitch looks like installed on our vehicle. Next we'll go ahead and give you a couple measurements to help you select some accessories for your hitch such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pin hole to the outer most edge of the bumper is approximately 4 inches. From the top of the opening in the receiver tube to the ground is approximately 13 1/2 inches. Now let's go ahead and install out hitch. To begin with lets go ahead and point out the locations that we use to mount our hitch to the vehicle. As you will see there are two weld nuts on each side, both the passenger and the driver side, as well as two holes at the center of the rear bumper bracing. more

Watch Video

10/17/2014 5:48:12 AM

Trailer Hitch Installation - 2006 Saturn Vue - Draw-Tite- Video

Today on our 2006 Saturn Vue we'll be installing the Draw-Tite Hitch part number 36408. Now here's what our hitch looks like installed on our vehicle. Next we'll go ahead and give you a couple measurements to help you select some accessories for your hitch such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pin whole to the outer most edge of the bumper is approximately 4 inches. From the top of the opening in the receiver tube to the ground is approximately 13 1/2 inches. Now let's go ahead and install out hitch. To begin with lets go ahead and point out the locations that we use to mount our hitch to the vehicle. As you will see there are two weld nuts on each side, both the passenger and the driver side, as well as two holes at the center of the rear bumper bracing. more

Watch Video

10/17/2014 5:47:38 AM

Trailer Hitch Installation - 2006 Saturn Vue - Curt- Video

Today on our 2006 Saturn Vue, we'll be installing the Curt Hitch, part number C12291. Here's what our hitch looks like installed on our vehicle. Now we'll go ahead and give you a couple measurements in helping you choose some accessories, such as a ball mount, bicycle rack, or cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is approximately 3" and from the top of the opening in the receiver to the ground is approximately 13 1/2". Now let's go ahead and install our hitch. To begin with, let's go ahead and point out the locations that we'll use to mount our hitch to the vehicle. more

Watch Video

10/13/2014 2:35:48 PM

Trailer Hitch Installation - 2006 Saturn Vue - Curt 13591- Video

Today on our 2006 Saturn Vue we'll be installing the Curt Hitch part number 13591. Here's what our hitch looks like installed on our vehicle. Now we'll go ahead and give you a couple of measurements in helping you choose some accessories for your hitch, such as a ball mount, bicycle rack or cargo carrier. From the center of the hitch pin hole to the outer most edge of the bumper is approximately 3 1/2 inches. From the top of the opening in the receiver to the ground is approximately 13 1/2 inches. To begin with let's go ahead and point out the locations that we use to mount our hitch to the vehicle. As you will see there are two weld nuts on each side, both the passenger and the driver side, as well as two holes at the center of the rear bumper bracing. These two holes will have to have a carriage bolt and a spacer block fish-wired into them. more

Watch Video

10/13/2014 2:35:33 PM

Trailer Hitch Installation - 2008 Saturn Vue - Curt- Video

Today on our 2008Saturn VUE, we'll be installing the CURT hitch, Part Number13594. Here's what the hitch looks like installed on a vehicle. Now we'll go ahead and give you a couple measurements in helping you choose some accessories for your hitch, such as a ball mount, bicycle rack, or cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is approximately 4inches, and from the top of the opening of the hitch to the ground is approximately 15inches.Now let's go ahead and install our hitch. To begin with, we will need to remove four exhaust hangers and lower the exhaust line out of the way. Before you remove any of the exhaust hangers, you want to make sure that you install a safety strap to help support the exhaust once the hangers have been removed. more

Watch Video

9/29/2014 4:35:42 AM

Trailer Hitch Installation - 2006 Saturn Vue - Hidden Hitch 87572- Video

All right. Today on this 2006 Saturn Vue, we're going to install Part Number 87572. This is from Hidden Hitch. Okay. First thing we're going to do is clean up the thread of holes, they're inside of the frame. Looking at the passenger side, you can see two threaded holes. more

Watch Video

12/28/2012 9:18:35 AM

Trailer Hitch Installation - 2009 Saturn Vue - Curt- Video

Today on our 2009 Saturn Vue, we'll be installing Curt Hitch, part number 13594. Now before we begin our installation, here's what your hitch will look like on the vehicle. We'll go ahead and give you a few measurements to help you in selecting accessories such as a drawbar, a bike rack, or a cargo carrier. From the center of the hitch pin hole to the outermost part of the bumper is 4 inches and from the top of the receiver tube to the ground is 14-1/4 inches. Now, let's go ahead with our install. To begin our installation, we'll need to lower the exhaust by removing the three exhaust hangers. more

Watch Video

11/21/2012 11:45:56 AM

Trailer Hitch Installation - 2007 Saturn Vue - Draw-Tite- Video

Today on our 2007 Saturn Vue, we'll be installing the draw-tight hitch, part number 36408. This is what our hitch will look like once installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is 4 1/4 inches. From the top of the receiver tube to the ground is 14 3/4 inches. This will assist you in selecting accessories such as a draw bar, a bike rack or a cargo carrier. more

Watch Video

11/13/2012 10:03:47 AM

Trailer Hitch Installation - 2007 Saturn Vue - Hidden Hitch- Video

Today on our 2007 Saturn Vue well be installing the Hidden Hitch, part number 87572. This is what our hitch will look like once its installed. Next well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is 4 inches. From the top of the receiver tube to the ground is 14 inches. This will assist you when selecting accessories such as a draw bar, a bike rack, or a cargo carrier. more

Watch Video

11/13/2012 4:05:48 AM

Trailer Hitch Installation - 2007 Saturn Vue - Curt- Video

Today on our 2007 Saturn Vue, we'll be installing the car hitch part number 13591. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is 4 1/2 inches. From the top of the receiver tube to the ground is 14 inches. This will assist you in selecting accessories such as a draw bar, a bike rack or a cargo carrier. more

Watch Video

11/13/2012 4:03:01 AM

Trailer Hitch Installation - 2009 Saturn Vue - Draw-Tite- Video

Today on this 2009 Saturn Vue, we're going to install part number 75556 from Draw-Tite. Now, this is what the hitch looks like once installed on the vehicle. Next, we'll give you some measurements that will help you out in selecting some accessories such as the ball mount or bicycle, or a cargo carrier. From the top of the receiver opening down to the ground is going to be 14 inches, and from the center of the hitch pin hole to the outside edge of the bumper is going to be 6-1/4 inches. Now, we'll go ahead and show you how the hitch is installed. The first step to install our hitch is to go ahead and lower the exhaust. more

Watch Video

7/6/2012 4:30:26 PM

Trailer Hitch Installation - 2009 Saturn Vue - Hidden Hitch- Video

Today on this 2009 Saturn Vue, we're going to install part number 87445 from Hidden Hitch. Now, this is what the hitch looks like when it's installed on the vehicle. Next, we'll give you some measurements that will help you out in selecting some accessories such as a ball mount or a bicycle rack, or a cargo carrier. From the top of the receiver opening down to the ground is going to be 14 inches and from the center of the hitch pin hole to the outside edge of the bumper is going to be 6-1/4 inches. Now, we'll go ahead and show you how the hitch is installed. Our first step to install our hitch is to go ahead and lower the exhaust. more

Watch Video

7/6/2012 12:50:58 PM

Trailer Hitch Installation - 2009 Saturn Outlook - Curt- Video

more

Watch Video

5/4/2012 2:38:50 PM

Trailer Hitch Installation - 2003 Saturn Vue - Curt- Video

Today on our 2003 Saturn Vue were going to be installing the Curt hitch part number C12291. Here are a couple of measurements that will assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is 2-1/2 inches, from the top of the receiver tuber to the ground is 13-1/2 inches. This will assist you in selecting accessories such as a drawbar, a bike rack, or a cargo carrier. Now, lets go ahead with the installation. For this application theres no tie down bracket to be removed. more

Watch Video

5/1/2012 4:07:47 PM

Trailer Hitch Installation - 2000 Saturn L Series- Video

Today on this 2000 Saturn L Series, we're going to install the Draw-Tite Hitch part number 24685. This will also be comparable to Hidden Hitch part number 60926. Alright, here are a couple measurements that will assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost point of the bumper is 4-1/2 inches. From the top of the receiver tube to the ground is 11-1/4 inches. Now lets go ahead with installation. more

Watch Video

3/2/2012 1:49:49 PM

Trailer Hitch Installation - 2008 Saturn Outlook- Video

Today on this 2008 Saturn Outlook we're going to install of part number 75528 from Draw-Tite. This will also apply to part number 87435 for Hidden Hitch. This is what the hitch looks like once installed on the vehicle. Next, we'll give some measurements that help you out in selecting the some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pin to the edge of the bumper were looking at 3 1/4" and from the top of the receiver opening down to ground were looking at 18-1/4". Now, we're going to show you how the hitches install. All right, we'll go ahead and show you how the hitch mounts up onto the frame. more

Watch Video

2/9/2012 11:06:39 AM

Trailer Hitch Installation - 2005 Saturn Relay- Video

Today is 2005 Saturn Relay, were going to install part number V82000 from Valley. This is what the hitch looks like when its installed. Next well give you some measurements to help you out selecting accessories such as a ball mount, a bicycle rack or a cargo carrier. From top of the receiver opening down to the ground, well be looking at 12 inches. If its from the center of the pinhole to the outside of your bumper its going to be 5 inches. Now well go and show you how the hitch is put on. more

Watch Video

2/2/2012 3:46:17 PM

Trailer Hitch Installation - 2004 Saturn Vue- Video

Today on this 2004 Saturn Vue we are going to install part number 13591 from Curt. We are looking at the passenger side of the frame. These are two threaded openings that we will use to attach the hitch on the vertical surface of the frame here. This is going to be identical on both sides of the vehicle. We will move to the bumper structure and we will show you the two openings here and here. Our next step is to inspect the threads on the frame of the vehicle itself. What we are going to do is spray it down with some lubricant. In this case we are going to use a tube cleaner about 1/ 2 inch diameter and just use that to clean out the threads with. The tube brush we are using is part number 814092. When you have it good and cleaned out, run your bolt in until you can get it started by hand and probably turn it with a wrench and it should be okay. 00:56 more

Watch Video

7/2/2010 2:43:43 PM

Trailer Hitch Installation - 2007 Saturn Ion- Video

Today on this 2007 Saturn Ion we are going to be installing Curt hitch part number 11447. We are underneath the vehicle looking at the drivers side frame rail, the first thing we need to do before we start installing our hitch is lower the exhaust down. Depending on your model, you may have two or three exhaust hangers to remove the exhaust off of. On this model we have just two, one here at the rear of the vehicle and one here at the forward side, just rearward of the exhaust. :25 more

Watch Video

5/27/2010 11:23:31 AM

Trailer Hitch Installation - 2003 Saturn Vue- Video

Today on this 2003 Saturn Vue we are going to be installing Curt hitch part number 13591. We are underneath the vehicle, we are going to point out the mounting holes for our trailer hitch. Starting at the center of the vehicle, just below the bumper we have two existing holes, these are going to provide our two center most attaching points for our trailer hitch. Into those two hole we are going to be mounting the 1/ 2 inch carriage bolt along with the 1-1/2 by 2 inch block. If we move to the outboard side of the frame, we have two existing weld nuts here at the end of the frame rail, one on top of each other, these are going to provide the two attaching points on the side of the frame. That is going to be the same on both the driver and passenger side. :37 more

Watch Video

8/31/2009 11:03:42 AM

  1